| Transmission Frequency: | | ISM 2.414 ~ 2.468 GHz | | Transmission Power: | | 10mW/CE; 2mW/FCC | | Unobstructed Effective Range: | | 100m (Min.) | | Modulation Mode: | | FM | | Operating Temperature: | | -10 ~ +50(Degree C) / +14 ~ +122(Degree F) | | Storage Temperature: | | -20 ~ +60(Degree C) / -4 ~ +140(Degree F) | | Operating Humidity: | | ≤85%RH | | Imaging Sensor Type: | | 1/4 inch Sharp CCD | | Picture Total Pixels: | | PAL:628 x 582 Pixels;
NTSC: 510 x 492 Pixels | | Horizontal Resolution: | | 420 TV Lines | | View Angle: | | PAL: 60/span>
NTSC: 40/span> | | Minimum Illumination: | | 0Lux | | Band Width: | | 20M | | Angular Field of View: | | 45(F=8mm) | | Power Supply: | | DC12V | | Receiving Frequency: | | ISM 2,400 ~ 2,483MHz | | intermediate Frequency: | | 480MHz | | Frequency Stabilization: | | 00KHz | | Demodulation Mode: | | FM | | Antenna: | | 50 ohm SMA | | Receiving Sensitivity: | | ≤-85dBm | | Video Output: | | 1Vp-p @ 75Ω, S/N>38dM | | Audio Output: | | 3Vp-p @ 600Ω | | Operation Temperature: | | -10 ~ +50 / +14 ~ +122C / F | | Operation Humidity: | | 85%RH | | Power Supply: | | DC +12V | | 1. | 420TV lines clear picture display. | | 2. | 4-channel available to Channel scan and channel skip for multi-camera usage. | | 3. | Built-in microphone for audio monitoring. | | 4. | Min. 100m transmission distance without block. | | 1. | Put the Camera in the place where need to monitor. | | 2. | Insert power Adapter, the DC Output Plug of power Adapter in the power Input jack of the Receiver. | | 3. | Use the AV Cable to connect one Channel of Audio and Video Input plugs of the TV set or Monitor. | | 4. | Press the off/on key of the Remote Control, or press the Channel key of the Receiver and open the power Adapter of the Receiver. The Receiver will acquiesce the Channel 1 after opening. | | 5. | Press the Channel key (marked No.1, 2, 3 and 4) of the remote control and make the Frequency of the Receiver corresponding to the transmitter Frequency of the Receiver. | | 6. | Can see the Video and listen to the voice through the television or monitor, adjust the place of the Camera, aiming at the monitoring object then can make the valid monitor. | | 7. | Press the ON/OFF key of the remote control, or press the Channel button on the Receiver for 3 seconds to turn off the power of the Receiver. | | The Problems And The Solutions : | | 1. | The indicator of the Channel display window is not lighting. Check whether the socket of the power Adapter works well or not, and make sure the power switch is turning on. | | 2. | The Receiver cannot receive picture or the picture-received flashes. | | a. | Please check whether the Wireless Camera have already put through the power. | | b. | Whether the distance between Wireless Camera and Receiver is too far or whether there is Electromagnetic shielding Barrier between Wireless Camera and Receiver (eg: Building of steel structure will make much hindrance to transmitting signal). | | c. | In the Range of Receiving, Don't make two Wireless Cameras with the same Frequency work at the same time, otherwise they will cause interfering. | | d. | When the transmitting Cameras of different Frequency work at the same time, the distance between the Cameras should be kept about or over 2 meters, otherwise receiving will be interfered. | | e. | If there are high-power transmission signals with the same Frequency and Car-mounted Radio working around, they will cause. | | 1 x 2.4GHz 4-Channel Remote Wireless AV Receiver | | 1 x Antenna for Receiver | | 1 x 2.4GHz, 1/4 inch SharpChip, 420TV Lines, Security CCTV Wireless CCD Color Camera | | 1 x Bracket for Camera | | 1 x AV Cable | | 1 x DC12V Adapter for Receiver | | 2 x DC12V Adapter for Camera | | "
It takes about 7-10 days days to deliver the goods to the United States and 10-15 days days to European countries and other countries.
Copyright © 2012 SPYONSALE.COM Ltd. All Rights Reserved.
| |
